Victron Energy Argo FET dual battery isolator 100A

Item number: 16544

Just like the diode load current distributors, the FET charging distributors allow you to charge two or more batteries simultaneously with one alternator (or a battery charger with a single output voltage).
In contrast to the diode load current distributors, the FET load current distributors have virtually no voltage loss.
The voltage drop is less than 0.02 volts at a low current and on average 0.1 volts at higher current values.

Category: isolating relay

102,35 €

including 16% VAT. , plus shipping (Paket)

Recommended retail price: 121,39 €
(You save 15.68 %, that is 19,04 €)
Not available at the moment!

Just like diode based battery isolators the FET variant is being used to charge one or more additional batteries off the generator/alternator or grid connected charger without combining the auxiliary batteries with the starter battery.

Important: Isolator relay, FET or any other more or less simple battery isolatation technology is only recommended, when connecting auxiliary batteries of the same type as the starter battery. Reason for this is the controller on the generator, which has a special cutoff voltage optimized for the chemistry of the starter battery. So if your car is equipped with a standard lead acid starter battery, you cannot use an isolator circuit to add a gel type battery to the system, because these gel types have different charging characteristics. If you want to mix battery types, you will need to use a so called A2B or B2B (alternator to battery or battery to battery) charger, which in turn adapts the voltage levels to the different cell type and also does the isolation for you. Additionally it is highly recommended to have the charge voltage temperature compensated, which can be done automatically by these units, when connected to a temperature sensor. See our inventory for a range of b2b charge controllers. Feel free to mail with questions.

The fundamental difference to a standard relay isolator is just this: Isolation. While standard relay will connect both batteries as soon as the engines runs, a FET isolator does not directly connect the batteries like that. A direct connection always means, that the stringer battery will feed the weaker battery. Thus, our good starter battery is being discharged by the emptied aux battery. Of course the running alternator will nor charge both batteries, but this conecpt implies, that you keep the engine running long enough to charge both batteries. That would of course result in zwo full batteries. But what if you drive just a short time? You will end up with the starter battery being lower than before. Do that 10 times, you you know what happens. Enter the FET isolator: Once the engine is running, it distributes charge current to the aux battery without ever touching the starter battery. So no matter how long you keep the engine running, the starter battery won't be emptied. This difference is important depending on your personal application, but you should keep that in mind. If you want emergency start, you will need to purchase a seperate battery switch - just like with any other isolator technology.

Compared to diode based battery isolators the voltage drop of FET isolators is marginal. Typically less than 0.02V at low currents, and around 0.1V at high currents. Nevertheless you should keep the connection wires as short as possible, because you want as much of the voltage of the alternator charge controller to reach your aux batteries. Essentially there is no practical reason for using diode based isolators anymore these days.

Argofet 100-2
Max. charge current: 100A
Max. generator current: 100A
Number of batteries: 2
Connection: M8 bolts

Dimensions (HxWxD): 120 x 200 x 68mm (incl. bolts)

Product weight: 1,30 kg
Average product review

Write your first review and help others with their purchase decision:



Batterieumschalter-Kit "Add a Battery Mini", 7649

146,17 € *
Available now

Batterieumschalter-Kit "Add a Battery", 7650

190,08 € *
Available now

Other customers also bought the following items

Planar Adapter 44D auf 90mm

11,65 € *
Available now

Planar air duct 60mm

11,65 € *
11,65 € per 1 m
Available now

air duct T, 60mm

11,65 € *
Available now